Consumers
Retailer Login

Metalizer

Plasti Dip Metalizer Enhancer is a shimmering, metallic finish while letting the color of the Plasti Dip underneath show through.

Plasti Dip Enhancers are specially designed to make the already-outstanding Plasti Dip home solution even better. These Enhancers are easy to use and will give any Plasti Dipped item a unique look.  With Plasti Dip Metalizer, can further customize the colors of the Plasti Dip projects. Metalizer is not intended for use on its own. Must be applied over Plasti Dip.

ATTRIBUTES OF PLASTIDIP®

  • Remains flexible and stretchy over time
  • Will not crack or become brittle in extreme weather conditions
  • Proven in temperatures from -30°F to 200°F
  • Easy to use application
  • Metallic finish

AVAILABLE COLORS

Silver
Copper
Graphite

Silver

Copper

Graphite

Become A Retailer

Product FAQ

The 14.5 oz. liquid can will cover  approximately 5 sq. ft. at 10 mils thickness. The 11 oz. spray will cover about 6 sq. ft. at 5 mils thickness.

Plasti Dip protective coating has a satin finish. If you are experiencing a cloudy or hazy finish, it’s likely caused by high humidity. Avoid these conditions or add approximately 5-10% naphtha to reduce the problem.

Dipping and removing too quickly can cause this. Remove at a rate of 1” every 5 seconds. If experiencing runs or sags when spraying, move can further away from the surface and apply a lighter coat. Sagging and dripping can also be caused by high humidity, high temperatures, windy conditions, or direct sunlight. Ideal conditions are low humidity, 16 degrees, little to no air movement in a well-ventilated area.

Most items being dip coated do not require priming because the coating is shrinking around the item as it dries. However, in extreme conditions or when adding protective coating to a large metal surface, primer is recommended. Use Plasti Dip Primer or a high quality acrylic auto body-type primer. Do not use Rust-Oleum® primer as it is not compatible.
Plasti Dip does not contain any heavy metals, and when completely dry, is considered harmless. However, it is not recommended that it be used on items that may be chewed or inserted into the mouth as it may present a choking hazard.
When following the directions, you can apply as many coats of Plasti Dip protective coating as you like. In most uses 10-12 mils thickness is adequate (2 dip coats, 3-4 brush coats, 4-5 spray coats). Greater thickness might be necessary for aesthetic reasons or in extreme cases.
Mixing different colors of Plasti Dip protective coating can be done to achieve other colors. Your local hardware, home center, or paint store may also sell tubes of tinting colors. Add approximately 1/3 of a 1 oz. tube per 14.5 oz. can of Plasti Dip.
While Plasti Dip has been used for dishwasher rack repair in the past, it is not recommended. Our ReRACK™ product is much better suited for this application and works very well.
Plasti Dip protective coating has excellent resistance to acids, alkaline, and most common household chemicals. However, it is best to test this before going ahead with your application. Plasti Dip does have limited resistance to petroleum-based products.
While Plasti Dip has excellent dielectric properties (insulates against shock), our Liquid Tape Electrical product is specifically formulated and conveniently packaged for this application.
Rub acetone or fingernail polish remover in an inconspicuous area and apply Plasti Dip to test for success.
Plasti Dip does not contain any polyvinylchloride or any other vinyl resins.
Yes, the Plasti Dip Enhancer in the Glossifier™ formulation provides a glossy finish on cured Plasti Dipped items. Plasti Dip Enhancers are formulated to bond only with the unique chemical structure of Plasti Dip and are not recommended for use on other surfaces.

Our Retailers

Your customers continue to trust the highest quality, flexible rubberized coatings, sealants, and adhesives on the market today – only from Plasti Dip International.
View Retailers

Get In Touch With Us

    ADDRESS

    Plasti Dip International
    Attn: Customer Service
    3920 Pheasant Ridge Drive
    Blaine, MN 55449

    PHONE NUMBER

    1.800.969.5432 ext. 6135

    EMAIL

    contact@plastidip.com
    logo-new-1

    About

    Products

    Where to Buy

    Resources

    Contact

    Consumers
    View Products
    Retailer Login